Product Categories

Temperature & Process Controller - PIXSYS ATR243

Dual display controller, 1/16 DIN, 48 x 48mm fascia, universal input with up to 4 outputs. Universal power supply 24-230V AC/DC.

Single analogue input configurable for up to 18 different sensors/signals. 2-4 Outputs configurable as relays (also as Open/Close logic for motorised valve control), SSR, 4-20mA, 0-10V signal (both for control or re-scalable retransmission of process/setpoint).

The switch mode power supply, with extended range 24-230Vac/Vdc, does not require any jumpers setting. Control modes: On/Off, PID + Autotuning, Heating/Cooling PID with neutral zone. Software features include the launch Tuning and the selection of 2-4 setpoints by digital input, the optional manual reset of output by frontal keyboard ("Limit controller"), Latch-on function for sensors calibration (including load cells), a programmable cycle of 3 steps.

Optional features are the serial communication RS485-ModbusRTU and load monitoring function (Loop Break Alarm) with current transformer TA.

Sealing IP65 with frontal gasket. Optional Memory Card to copy all parameters, available also with internal battery therefore not requiring to power up the unit. Software application LABSOFTVIEW for Windows enables setting and monitoring of parameters on PC. UL-CSA approved for North-American market.

Overview
Technical Information
Installation
Downloads

SIZE: 48 x 48 (fascia) x 122.5mm (deep)
SUPPLY: 24-230 Vac / Vdc +/- 15% 50/60Hz
CONSUMPTION: 3W
DISPLAY: dual 4 digits, 8 red LEDs, decimal point
OPERATING CONDITIONS: 0-45°C, 35..95rH%
INPUTS: 1 configurable TC K, J, S, R, PT100 (2ranges), NI100, PT1000, PT500, PTC1K, NTC10K,0-10V, 0/4-20mA, 0-40mV, Potentiometer 6KΩ / 150KΩ, TA 50mA.
OUTPUTS: ATR243-20ABC : 2 relays 5A resistive OR 1 relay + 1 logic SSR 12V-30mA / 4..20mA / 0...10Volt for control or retransmission (4000 points accuracy), ATR243-21ABC-T : 2 relays 5A resistive + 1 logic SSR 12V-30mA / 4..20mA / 0...10Volt for control or retransmission (4000 points accuracy) + RS485 Modbus RTU (57600 baud max) + Input TA 50ma for Loop Break Alarm, ATR243-31ABC : 3 relays 5A resistive + 1 logic SSR 12V-30mA / 4..20mA / 0...10Volt for control or retransmission (4000 points accuracy) + Input TA 50ma for Loop Break Alarm
DIGITAL INPUT: Tuning Start, Setpoint change, selection Man/Auto, Hold function, Start/Stop pre-programmed cycle
CONTROL MODES: ON/OFF, P, PI, PID, Autotuning
ACCURACY: 0.5% ±1digit for TC/RTD; 0.2%±1digit for V/mA
SAMPLING TIME: selectable (max 15ms)
SEALING: IP54 Frontal (IP65 with gasket), IP30 Box, IP20 Terminal blocks
CONFIGURATION: Parameters protected by password, Memory card with battery for serial productions, software for parameters settings on PC.
CERTIFICATIONS : CE CSA UL

Control Modes

ON/OFF, P, PI, PID, Continious tuning

Input - Number and Types

1 universal TC, RTD, DC linear mA/mV, Potentiometer, CT 50mA, 1 Digital Input

Outputs - Number and Types

4 Max : Relay, SSR, DC linear V or mA

Profile Programming

Communication

RS485 Modbus RTU

Supply Voltages

AC/DC 24 to 230V +/- 15% 50/60Hz

Panel Sealing

IP54 Frontal (IP65 with gasket), IP30 Box, IP20 Terminal blocks

Approvals

CE CSA UL

Dimensions and Fixing Holes

48 x 48 (fascia) x 122.5mm (deep)

Operating Temperature

0 deg. C to 45 deg. C

Operating & Installation Manual

Click here to register and download the Operating & Installation Manual

Additional Information

APPLICATION_NOTE_ATR243_0211.pdf

Name:
Surname:
Email:
Company:

Name:
Surname:
Email:
Company:

Name:
Surname:
Email:
Company:

Name:
Surname:
Email:
Company:

Name:
Surname:
Email:
Company:

Temperature & Process Controller - PIXSYS ATR243

Dual display controller, 1/16 DIN, 48 x 48mm fascia, universal input with up to 4 outputs. Universal power supply 24-230V AC/DC.

Please register to access our files.

Please register to access our files.

Please register to access our files.

Please register to access our files.

Please register to access our files.